| Last Modified: 11-29-2007 | 1.6 J | |
| Service Category: Vehicle Exterior | Section: Mirror (ext) | |
| Model Year: 2008 | Model: Sequoia | Doc ID: RM000002Y46007X |
| Title: MIRROR (EXT): POWER MIRROR CONTROL SYSTEM (w/ Memory): SYSTEM DESCRIPTION (2008 Sequoia) | ||
|
Power Retractable Mirrors do not Operate with Power Retract Mirror Switch |
SYSTEM DESCRIPTION
This circuit detects the conditions of the mirror retract switch.
The outer mirror switch sends information about the operating condition of the mirror retract switch (switch input signals) through the CAN communication line. Then the switch input signals are sent to the outer mirror control ECU.
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
|
1. |
CHECK DTC |
(a) Use the Techstream to check if the CAN communication system is functioning normally
.
Result
|
Result |
Proceed to |
|---|---|
|
CAN DTC is not output |
A |
|
CAN DTC is output |
B |
|
|
2. |
READ VALUE USING TECHSTREAM (MIRROR RETRACT SWITCH) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream ON.
(d) Enter the following menus: Body Electrical / Main Body / Data List.
(e) According to the display on the Techstream, read the Data List.
Main Body
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Outer Mirror Fold SW |
Mirror retract switch signal / ON or OFF |
ON: Switch is on (retracting) OFF: Switch is off |
- |
OK:
On the Techstream screen, each item changes between ON and OFF according to above chart.
|
|
3. |
PERFORM ACTIVE TEST USING TECHSTREAM (MIRROR RETRACT FUNCTION) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream ON.
(d) Enter the following menus: Body Electrical / Mirror / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
Mirror
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Mirror Fold |
Mirror retract operation |
FOLD/OFF |
- |
|
Mirror Return |
Mirror retract operation |
RETURN/OFF |
- |
Result
|
Result |
Proceed to |
|---|---|
|
Outer rear view mirror operates normally |
A |
|
Outer rear view mirror LH does not operate normally |
B |
|
Outer rear view mirror RH does not operate normally |
C |
|
|
4. |
INSPECT OUTER MIRROR SWITCH (MIRROR RETRACT SWITCH) |
|
(a) Remove the switch
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
7 (MR) - 4 (E2) |
Pressed (Driving position) |
Below 1 Ω |
|
Not pressed |
10 kΩ or higher |
|
|
8 (MF) - 4 (E2) |
Pressed (Retracts) |
Below 1 Ω |
|
Not pressed |
10 kΩ or higher |
|
|
5. |
CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH - MAIN BODY ECU AND BODY GROUND) |
|
(a) Disconnect the H1and H3 ECU connector. |
(b) Disconnect the J6 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
J6-4 (E2) - Body ground |
Always |
Below 1 Ω |
|
J6-7 (MR) - H1-9 (AMR) |
Always |
Below 1 Ω |
|
J6-7 (MR) - Body ground |
Always |
10 kΩ or higher |
|
J6-8 (MF) - H3-6 (RET) |
Always |
Below 1 Ω |
|
J6-8 (MF) - Body ground |
Always |
10 kΩ or higher |
|
|
6. |
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH |
|
(a) Remove the mirror LH
|
(b) Check the retractable mirror's movement.
(1) For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
OK:
|
Measurement Condition |
Mirror Position |
Specified Condition |
|---|---|---|
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Forward position (A) |
Moves from (A) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Forward position (A) |
Does not move |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Position between forward position (A) and driving position (C) |
Moves from (B) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Position between forward position (A) and driving position (C) |
Moves from (B) to forward position (A) |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Driving position (C) |
Moves from (C) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Driving position (C) |
Does not move |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Position between driving position (C) and retracted position (E) |
Moves from (D) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Position between driving position (C) and retracted position (E) |
Moves from (D) to driving position (C) |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Retracted position (E) |
Does not move |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Retracted position (E) |
Moves from (E) to driving position (C) |
NOTICE:
- Disconnect and reconnect the battery once between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
|
|
7. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR LH - OUTER MIRROR CONTROL ECU) |
|
(a) Disconnect the M7 ECU connector. |
(b) Disconnect the M5 mirror connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
M5-7 (MR) - M7-1 (MR+) |
Always |
Below 1 Ω |
|
M5-7 (MR) - Body ground |
Always |
10 kΩ or higher |
|
M5-8 (MF) - M7-2 (MR-) |
Always |
Below 1 Ω |
|
M5-8 (MF) - Body ground |
Always |
10 kΩ or higher |
|
|
8. |
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH |
|
(a) Remove the mirror RH
|
(b) Check the retractable mirror's movement.
(1) For each mirror position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.
OK:
|
Measurement Condition |
Mirror Position |
Specified Condition |
|---|---|---|
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Forward position (A) |
Moves from (A) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Forward position (A) |
Does not move |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Position between forward position (A) and driving position (C) |
Moves from (B) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Position between forward position (A) and driving position (C) |
Moves from (B) to forward position (A) |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Driving position (C) |
Moves from (C) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Driving position (C) |
Does not move |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Position between driving position (C) and retracted position (E) |
Moves from (D) to retracted position (E) |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Position between driving position (C) and retracted position (E) |
Moves from (D) to driving position (C) |
|
Battery positive (+) → Terminal 7 (MR) Battery negative (-) → Terminal 8 (MF) |
Retracted position (E) |
Does not move |
|
Battery positive (+) → Terminal 8 (MF) Battery negative (-) → Terminal 7 (MR) |
Retracted position (E) |
Moves from (E) to driving position (C) |
NOTICE:
- Disconnect and reconnect the battery once between each mirror position check.
- The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.
|
|
9. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR RH - OUTER MIRROR CONTROL ECU) |
|
(a) Disconnect the M7 ECU connector. |
(b) Disconnect the L6 mirror connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
L6-7 (MR) - M7-5 (MR+) |
Always |
Below 1 Ω |
|
L6-7 (MR) - Body ground |
Always |
10 kΩ or higher |
|
L6-8 (MF) - M7-6 (MR-) |
Always |
Below 1 Ω |
|
L6-8 (MF) - Body ground |
Always |
10 kΩ or higher |
|
|
|